- Can I reset my NBN box?
- How many lights should be on my NBN box?
- How can I tell if my router is bad?
- Why is the online light on my modem not on?
- What do the lights mean on my Telstra smart modem?
- What does red light mean on Telstra smart modem?
- What should the lights on my modem look like?
- What do lights on NBN box mean?
- What do the lights on the modem mean?
- What lights should be on NBN modem?
- Why does my modem randomly stop working?
- What Colour should the lights be on my Telstra modem?
Can I reset my NBN box?
To reset your nbn™ Connection Box: First, turn off the power to your connection box by unplugging it from the wall power outlet.
Next, remove the power cable from your connection box and wait 2 minutes.
Reconnect the cable and turn the power back on..
How many lights should be on my NBN box?
four lightsThe four lights on the top of the nbn™ connection box can tell you a lot about your connection.
How can I tell if my router is bad?
To test if your router is working, try to ping one computer using another computer in the same network. You should be able to do this if the router is working properly. Your computer’s firewall must be disabled as well. To learn more on how to check the computer’s connectivity with the router, click here.
Why is the online light on my modem not on?
Online light: Off Assuming that the other indicators on your modem/gateway (covered above) aren’t exhibiting any problems, the Online light failing to illuminate may mean that there is a problem with the modem configuration or the service has not been activated.
What do the lights mean on my Telstra smart modem?
Both Link, Online and Phone light should be green. The Signal light indicate strength of 4G backup and should be either red (Poor Signal), orange (Signal OK) and Green (Good Signal) https://crowdsupport.telstra.com.au/t5/News-Feed/What-do-the-lights-on-your-Telstra-modem-mean/ba-p/…
What does red light mean on Telstra smart modem?
A solid red light on the front of the modem indicates that both the 4G backup and main connection are not working. As you still have internet then it could be a fault causing light to turn red. Sometimes this can be fixed by turning modem off for 5 minutes and then back on.
What should the lights on my modem look like?
In general, when everything is working correctly the modem lights should look like: Power light: green (solid) DSL light: green (solid) Internet (INT) light: green (flashing)
What do lights on NBN box mean?
The lights on your nbn™ Connection Box tell you about the status of your connection. If you have an HFC nbn connection, the lights on your box will look like this: When it starts up, each light should flash as the nbn Connection Box connects to the nbn network. Once it’s connected, all lights should go green.
What do the lights on the modem mean?
POWER: A solid green light indicates the unit is properly connected to power. A blinking red light indicates a possible modem failure. … If your modem is connected to power, and yet no lights are lit, check to ensure the power switch on the back is toggled to the “on” position.
What lights should be on NBN modem?
Popular SearchesLightIndicatorMeaningPowerFlashing greenYour nbn connection box is starting up.OpticalOffSomething external has disabled your nbn Connection BoxSolid redYour nbn Connection Box has lost connection with the network.Solid greenYour nbn Connection Box is connected and working properly.18 more rows
Why does my modem randomly stop working?
Reboot your modem and router. Sometimes Internet service providers (ISP) make changes on their end that can change the settings that connect your router to the Internet. The way to fix this is to unplug both your modem and your router (you may have one piece of equipment that acts as both) and wait a full 60 seconds.
What Colour should the lights be on my Telstra modem?
You want to see a green flashing light, as solid green means the connection box is in test mode. A flashing amber light means the device is starting up and installing, while red indicates a system fault. If you see a red light, power cycle the Connection Box.